Home › Flat Roof Installations in Cheshire › EPDM Rubber Roofing
EPDM membranes

EPDM Rubber Roofing: How a Flat Roof Membrane Works

EPDM is a flexible synthetic rubber sheet used to waterproof flat roofs. Here is how it is laid, where it suits and what to check before you agree to it.

What EPDM rubber roofing is

EPDM is a synthetic rubber membrane supplied in large rolls. On a flat roof it is laid over a prepared deck as a single sheet, so there are far fewer seams than you would get with overlapping layers of felt. The sheet is flexible, which lets it move a little with the building instead of cracking.

It is most often used on garages, single-storey extensions, porches and dormer tops, where the roof is a fairly simple shape and the membrane can be cut from one piece.

Signs your existing flat roof may be ready for a new membrane

Most people only think about it once water is coming through the ceiling, but there are usually warnings first. If you are searching for flat roof replacement or a new rubber roof, these are the things that tend to prompt it:

  • Ponding water that stays on the surface for days after rain.
  • Blistering, splits or open seams in an older felt or bitumen covering.
  • Stained or sagging ceilings below the roof.
  • Repeated patch repairs that keep failing in different places.
  • Moss or plant growth in the lap lines and at the edges.

What the installation involves

The detail depends on the roof, but the work generally follows the same order.

  • The old covering is stripped, or assessed to see whether it can stay as a base.
  • The deck is checked for rot or movement. Damaged boards or joists are cut out and replaced.
  • Insulation is laid if the design calls for it, with a suitable falls arrangement so water runs to the outlet.
  • The membrane is bonded or ballasted according to the system, then cut and dressed around upstands.
  • Edges are finished with trims, and the roof is checked at corners, penetrations and wall junctions.

A good installer spends most of the time on the preparation and the details. The large sheet itself is the quick part. Corners, pipes and where the roof meets a brick wall are where leaks usually start, so these are the areas worth asking about.

What affects the choice of EPDM

EPDM suits many roofs but not every one. It depends on the condition of the deck, the shape of the roof, how many things poke through it and how much foot traffic it will see. A roof with a lot of awkward angles may suit a different system better.

The existing structure matters too. A deck that is sound and flat enough to drain can take a new membrane. A deck that has moved, or that holds water because the falls are wrong, needs correcting first, otherwise the new roof inherits the old problem.

A new membrane is only as good as what is underneath it. If a roofer quotes for EPDM without looking at the deck, the falls and the edge details, ask them to go back and inspect first.

When a repair is not enough

Small punctures and a failed seam can sometimes be patched. A roof that has gone soft underfoot, has widespread splits, or has been patched several times is usually past that point. Putting a new covering over wet insulation or rotten boards traps the damage, so we would rather open it up and see.

Questions to ask any roofer

  • Will the deck be inspected and any rot replaced before the membrane goes on?
  • How will water drain, and what are the falls?
  • How are the edges, corners and wall junctions finished?
  • Is the old covering coming off, and where does it go?
  • Does the design involve anything that may need building regulations or council consent? Check with your local council if you are unsure.

If you are thinking about EPDM rubber roofing in Cheshire or the surrounding area, we are happy to look at the roof and explain the options. A free quotation is available. Call to discuss your roof.

Want this looked at?

Call or message Apex Roofing for a free quotation.

Questions on this topic

Is EPDM suitable for a garage roof?

Often, yes. Garage roofs are usually simple shapes, which suits a single sheet. It still depends on the condition of the deck and how the water drains, so the roof needs inspecting first.

Can EPDM go over an old felt roof?

Sometimes, if the old covering is dry, sound and compatible. If the felt is wet, blistered or hiding rotten boards, it is normally stripped back so the deck can be checked.

What happens at the edges and corners?

They are finished with purpose-made trims and careful folds or corner pieces. These details matter more than the main sheet, so it is worth asking how your roofer will deal with them.

More Flat Roof Installation Guides

All Flat Roof Installation information →

Our Work

Recent Flat Roof Installation Jobs

Real jobs photographed by Apex Roofing.

See all our projects →

Areas We Cover

Flat Roof Installation Across Cheshire and Nearby

Apex Roofing covers Cheshire and the surrounding area. Choose your town for local information.

Find Us

Local Roofing Contractors Covering Cheshire

Apex Roofing Cheshire · 5 Weybridge Close, Warrington WA4 5LZ

📞

Telephone

07377 461095

💬

WhatsApp

+44 7465 861265

Free Quotation

Get a Free Quote

Tell us about the property and what you have noticed and we will come back to you.

Prefer to talk? Call 07377 461095 · WhatsApp +44 7465 861265 · Email apexroofing14@gmail.com